|
|
Taking the test flight to see if I wanna buy the venerable SV650.
Viewed: 3409 times.
|
Riding another SV (the ugliest SV the world has ever known), just to be sure
Viewed: 4938 times.
|
Here it now sits in the garage
Viewed: 4511 times.
|
Atop the table, this is how the bike has spent most of its time since I took ownership
Viewed: 2760 times.
|
The stunning, adjustable rearsets, and billet woodcraft case cover. Mmmmmm.
Viewed: 2638 times.
|
Sedately waiting for warmer weather, some race paint and possibly an alternative front end! Hmmmm.... ;)
Viewed: 2407 times.
|
Getting the SV ready to swap the front-end with a 636 donor.
Viewed: 4825 times.
|
The old top, triple clamp is removed and set aside for the machinist
Viewed: 2646 times.
|
The crowned, top nut should be loose enough to remove with your hand.
Viewed: 2423 times.
|
The stack of parts to go to the machinist for him to do his magic.
Viewed: 4452 times.
|
The top bearing race, inside the frame, appears to be in prefect condition!
Viewed: 4395 times.
|
As does the more critical lower, bearing race.
Viewed: 2537 times.
|
Here's how the SV faired during its first Dyno Run. Running rich, right into the basement.
Viewed: 2811 times.
|
First thing to do is to remove the tank.
Viewed: 2437 times.
|
The clamps holding on the air box were missing or extremely loose. The airbox was barely sitting there.
Viewed: 2207 times.
|
Carbs removed. Be very careful of the choke cables, and remember to unhook the idle screw before separating from the bike.
Viewed: 2093 times.
|
After going to 132 front and 130 rear main jet and installing a dynojet needle, on the setting one lower from middle, this is how things came out! I'm thrilled!!
Viewed: 2371 times.
|
And most importantly, the new front forks. They are going to be sooooo nice!
Viewed: 2309 times.
|
A new front wheel with rotors! (probably could use some paint).
Viewed: 2142 times.
|
An experiment. I sprayed the front wheel with brake caliper paint (with ceramic). We'll see how it holds up.
Viewed: 2202 times.
|
Pretty new petal rotors were then bolted to the black wheel.
Viewed: 1971 times.
|
The SV stem now resides in the 636 lower triple clamp. Now for the upper-triple clamp.
Viewed: 1885 times.
|
Sanding begins with the Z1000 front fender
Viewed: 1758 times.
|
Say goodbye to blue...
Viewed: 4041 times.
|
The first coat of sandable primer finds its way onto the Sharkskinz!
Viewed: 2104 times.
|
It already looks so much better than the gel-coat cream color.
Viewed: 1718 times.
|
Spending extra time to remove the "SUZUKI" decal appears to have paid off.
Viewed: 1633 times.
|
At least everything is the same color now...
Viewed: 1663 times.
|
The upper triple clamp is going to need some work. A spacer needs to be built for the stem and the stalks that hold the key are all wrong!
Viewed: 1743 times.
|
The stalks that hold the ignition in place are too long and the wrong angle.
Viewed: 1882 times.
|
It now takes the SV key beautifully!
Viewed: 4043 times.
|
The fork tubes are then inserted
Viewed: 2072 times.
|
The stepped top triple clamp is going to require another spacer :(
Viewed: 1676 times.
|
Dimensions for the headset spacer
Viewed: 4606 times.
|
The front wheel is then bolted on
Viewed: 2183 times.
|
A 10mm spacer will be required to fit ZX-10 petal rotors onto the 03/04 636 forks.
Viewed: 4079 times.
|
Dad got involved and turned my drawing into these!
Viewed: 1932 times.
|
The 10mm spacers fit perfectly!
Viewed: 3764 times.
|
I had to slip the primed tank onto the bike to get an idea of how it'll look
Viewed: 1858 times.
|
